Tap Repairs in Bardon
Tap repairs Bardon homeowners book most often come down to a worn washer, a tired cartridge or a perished O-ring. A licensed plumber sets each one right in a single visit. We fix taps across Bardon and the suburbs around it, from two-handle classics in older weatherboard houses to mixers on new benches.
If we're late, $100 comes off your bill
- Licensed and InsuredEvery job done by a licensed plumber. QBCC No: 15024607
- Fixed Quote FirstFlat-rate pricing, agreed before any work starts
- Lifetime Labour WarrantyBacked by our Fix-It-or-It's-Free guarantee (T&Cs apply)
- $0 Call-Out FeesNo extra charge for nights, weekends or public holidays
How Tap Type Decides the Repair
A washer tap shuts off when a soft washer bears onto its valve seat, while a mixer seals on ceramic discs inside a cartridge. The repair follows straight from that difference.
The two-handle washer tap
A washer tap gives a handle each to hot and cold, and each handle winds through several turns. The washer rides below the spindle, and winding the handle bears the washer down on its seat to close the flow.
The jumper valve
A jumper valve is the brass piece under the spindle of a washer tap, lifting the washer off the seat and dropping the washer back as the tap works. When a washer tap drips, the fault usually sits somewhere in that trio of spindle, valve and seat.
The single-lever mixer
A mixer blends hot and cold through one lever and usually turns just a quarter turn. Inside sits a ceramic disc cartridge: two polished discs that rotate onto and away from each other.
A worn cartridge is replaced whole, matched to the right model for the make, because sizes and fittings differ. A stiff or sticky lever usually traces to a gritty or worn cartridge, or a spindle gone dry. For the full fixture list across both rooms, see our tap and toilet plumbing page.
Tap Repairs for Owners and Tenants
Queensland opens one tap job to everyone: swapping a jumper valve or a washer, which the QBCC treats as unregulated work for anyone with the skill. The standards still apply, so the job has to come out right.
Everything past that washer is licensed. Fitting a complete new tap is the QBCC's own example of work an owner cannot do unlicensed. Other tap repairs count as minor work: a licensed plumber carries them out, with no permit and nothing lodged.
Rentals run on a different clock. A tap repair the tenancy Act does not list as an emergency is routine: the tenant reports the drip, and the owner or property manager has to sort the repair within a reasonable time. If nothing happens, a Notice to remedy breach (Form 11) gives the property manager or owner seven days or more to fix the breach.
Tap Leaks at the Spout, Handle and Base
Water dropping from a spout that has been shut off points to a failed sealing part, while water around the handle or a wet base points somewhere else. Where the water shows is the diagnosis:
Dripping spout
on a washer tap the washer or its seat has failed; on a mixer the cartridge has worn. A slow drip wastes thousands of litres over time.
Handle leak
water creeping around the spindle while the tap runs means a worn O-ring or a perished spindle seal, and the fix is a new ring.
Wet base
O-rings gone hard, a loose feed under the bench, or a crack in the body itself.
Shut the water down before touching any of those. Where a fixture has no isolation valve nearby, the stop tap at your meter closes the supply clockwise. Check first that nothing such as the hot water system depends on that supply while the stop tap is closed.
Garden and hose taps cop the weather year-round, so outdoor tap repairs have a page of their own. A running cistern is a separate job, covered on our toilet repairs page.
What Affects the Cost of a Tap Repair
The price moves with the tap type, the part it needs, the state of the seat and body, and how easily the water shuts off at the fixture. We set the figure in a fixed quote once we have seen the job.
Tap type
a mixer needs its cartridge matched to the make, while a washer tap usually needs a washer and a seat check.
Which part
washers, O-rings and cartridges are different jobs with different parts.
Seat and body
a rough seat needs dressing, and a body split or corroded through means a new tap.
Access and count
an isolation valve at the fixture beats shutting the whole house down, and how many taps you book changes the job size.
One more driver: a leak that survives new washers and cartridges points to replacing the tap rather than repairing it.
Older Houses, Older Taps
Bardon builds slowly. Area-level approvals counted 129 new dwellings across the five years to 2025, only 20 of them in 2021-22, while resident numbers grew about 6.0 per cent in the same period.
So the taps we get called to mostly serve houses built from the 1940s through the 1960s, like the weatherboard places dropping away from the ridge near Bardon State School. Worn spindles, brass seats gone oval and mixers from past renovations running on tired cartridges are the daily bread of our regular run.
How Your Tap Repair Visit Runs
- 1
Tell us what's happening
Call (07) 3524 7163 or send the form with a few details about the problem in Bardon. A clear description helps us bring the right parts.
- 2
We strip the tap and diagnose
We shut the water off at the fixture or the meter, strip the tap on the spot, and check the washer or cartridge against the seat and body. You hear which part has worn before anything is replaced.
- 3
Approve a fixed price
You get a fixed quote before any work starts, with flat-rate pricing and no hidden fees. Nothing goes ahead until you say yes.
- 4
Pay when it's finished
Pay by card or EFTPOS on site once the job's done, or ask about Fix now, pay later.
Plumbing job in Bardon?
$0 call-out fees, available 24/7, and same-day where we can.
Tap Questions We Hear Most
Call (07) 3524 7163How can I stop my tap dripping?
Find the part that seals and renew it. On a washer tap that part is the washer pressed onto its seat; on a mixer it is the ceramic disc cartridge. Queensland rules let anyone with the skill swap a jumper valve or washer, provided the work meets the standards, and any other tap work is for a licensed plumber.
Why is my mixer tap leaking around the base?
Three usual culprits. The O-rings around the collar or spout perish, a feed pipe under the bench works loose, or the body cracks. The first two are straightforward repairs; a cracked body means a new mixer.
Why is my mixer tap so stiff to turn?
Stiffness usually points to a cartridge gone gritty inside, or a spindle that needs cleaning and fresh grease. A worn cartridge comes out whole and the replacement has to match the model, because sizes differ between makes. We can tell you whether the mixer is worth rebuilding or past it.
What should a leaking tap repair cost in Bardon?
The price depends on the kind of tap, the part needed, seat or body damage, how simply the supply shuts off, and how many taps are done. We set the figure in a fixed quote after inspecting the tap, and nothing starts before you approve it.
Is an old tap in Bardon worth repairing?
Yes, while the body is sound. A worn washer, O-ring or cartridge is a quick job on a solid tap. A body cracked or heavily corroded, or a drip that survives new parts, points to a replacement instead.
Ring Us About Your TapWe'll call you back.
Ring (07) 3524 7163 and tell us what's wrong. You get $0 call-out fees, a fixed quote before any work starts and same-day where we can, 7 days a week.
To claim your $0 call-out fee, call (07) 3524 7163 today.